Products 1-24 of 45
Show
Availability: Temporarily Unavailable
Item #: PWR-48DC24 -
DC/DC converter with wide ranging input voltage and fixed 24C outputInput Voltage: DC 37V to 60VOutput Voltage: DC 24VOutput current: 5A. Max 10AAdopts synchronous rectification technology, low heat and high efficiencyAluminum shell, waterproof, shockproofMultiple protection function: output over-current protection, soft-start protection, chip over-temperature protection (No reversal protection, do NOT reverse)Working temperature: -40 °c ~ +85 °c (industrial temperature)Efficient...
Availability: Temporarily Unavailable
Item #: CABLE-S_PWRCTL -
Cable for connecting PwrCtl voltage to the SDC/SBL controllersRTQ-CABLE-S_PWRCTL
Availability: Temporarily Unavailable
Item #: CABLE-S_PWRCTL -
Availability: Temporarily Unavailable
Item #: BOB15 -
Break-out board with 15-pin male DSub connector. Plugs in all Roboteq motor controllers equipped with 15-pin connectors: SDC2xxx, MDC1xxx, MDC2xxx, XDC2xxx, SBL1xxx, MBL1xxx. Brings all of the controller's IO to pads for easy soldering of potentiometers, switches, relays or other accessories. A 9-pin female DSub connectors carries the controller's RS232 signals for direct connection to PC's standard COM port. Use not included 9-pin DSub to 9-pin DSub cable for PC to break-out board...
Availability: Temporarily Unavailable
Item #: CABLE-RC2 -
15-pin male DSub connector with 3 standard jacks for RC radios. Plugs in all Roboteq motor controllers equipped with 15-pin connectors: SDC2xxx, MDC1xxx, MDC2xxx, XDC2xxx, SBL1xxx, MBL1xxx.RTQ-CABLE-RC2
Availability: Temporarily Unavailable
Item #: CABLE-ABCX1 -
Single row ABC Hall Cable and transition board for Brushless Motor Controllers. Includes 6-pin Microfit connector for MBL1xxx, HBL1xxx single-channel controllers and for SBL2xxx, GBL2xxx dual channel controllers. Use two cables for dual channel controllers. Transition board has GND, 5V, A, B C solder pads pads for connecting hall sensors.RTQ-CABLE-ABCX1
Availability: Temporarily Unavailable
Item #: CABLE-ENC1 -
12" Cable and transition board for connecting two encoders to Brushed Motor Controllers. Includes 6-pin Microfit connector for MDC2xxx and XDC2xxx dual-channel controllers. Transition board has two sets GND, 5V, A, B solder pads pads for connecting encoders.RTQ-CABLE-ENC1
Availability: Temporarily Unavailable
Item #: CABLE-RC5 -
25-pin male DSub connector with 3 standard jacks for RC radios. Plugs in all Roboteq motor controllers equipped with 25-pin connectors: FBL2xxx, FDC3xxx, FIM2xxx, SBL2xxx, RGBL1xxx, RGBL1xxx, RGDC1xxx, RGIM1xxx, HDC2xxx, HBLxxxxRTQ-CABLE-RC5
Availability: Temporarily Unavailable
Item #: CABLE-ABCX2 -
ABC Hall Cable and transition board for dual channel Brushless Motor Controllers. Includes dual row 2x5-pin Microfit connector for FBL2xxx, FIM2xxx, HBL2xxx dual channel controllers. Transition board has two sets of GND, 5V, A, B C solder pads pads for connecting hall sensors.RTQ-CABLE-ABCX2
Availability: Temporarily Unavailable
Item #: CABLE-ABCX1M -
Single row ABC Hall Cable and transition board for Brushless Motor Controllers. Includes 5-pin miniature JST connector for SBL1xxx controllers. Transition board has with GND, 5V, A, B C solder pads pads for connecting hall sensors.RTQ-CABLE-ABCX1M
Availability: Temporarily Unavailable
Item #: CABLE-USB-232-CONV -
The USB-232-CONV converter allows the connection of a PC USB port to the RS232 port of a Roboteq controller, allowing the PC communication to the controller in these instances where a direct USB connection is not desired.RTQ-CABLE-USB-232-CONV
Availability: Temporarily Unavailable
Item #: CABLE-DS9 -
9 pin D-Sub cable six feet length male/female9 pin D-Sub cable six feet length male/female.RTQ-CABLE-DS9
Availability: Temporarily Unavailable
Item #: BOB25F -
Break-out board with 25-pin male DSub connector. Plugs in all Roboteq motor controllers equipped with one 25-pin connectors: FBL2xxx, FDC3xxx, FIM2xxx, SBL2xxx, RGBL1xxx, RGBL1xxx, RGDC1xxx, RGIM1xxx. Brings all of the controller's IO to pads for easy soldering of potentiometers, switches, relays or other accessories. A 9-pin female DSub connectors carries the controller's RS232 signals for direct connection to PC's standard COM port. Use not included 9-pin DSub to 9-pin DSub cable for PC to...
Availability: Temporarily Unavailable
Item #: CABLE-BOB15 -
Break-out board with 15-pin male DSub connector. Plugs in all Roboteq motor controllers equipped with 15-pin connectors: SDC2xxx, MDC1xxx, MDC2xxx, XDC2xxx, SBL1xxx, MBL1xxx. Brings all of the controller's IO to pads for easy soldering of potentiometers, switches, relays or other accessories. A 9-pin female DSub connectors carries the controller's RS232 signals for direct connection to PC's standard COM port. Includes 9-pin DSub to 9-pin DSub cable for connection to a PC. Replaces obsolete RS1...
Availability: Temporarily Unavailable
Item #: RS232-Isolator -
This product optically isolates the three RS232 lines: Tx, Rx and GND. This will protect your serial devices from transient surges and ground loops up to 5000V in each direction. It is port powered so no external power is necessary.RTQ-RS232-Isolator
Availability: Temporarily Unavailable
Item #: RS232-TTL-Adapter -
This adapter helps to convert TTL (Transistor-Transistor Logic) level signals to RS232 interface of the RoboteQ motor controllers.This converter has a Male DB9 connector, suitable for use with RoboteQ BOB15 and BOB25 break-out boards.Compatible with Arduino, Raspberry Pi, and any other micro controller that uses TTL serial communication.Ultra compact board size: 15 x 14 mm, DB9 Male Connector (RS232), supports 3V to 5.5V power supply, 4 pin through hole: GND, Logic out (TX), Logic In (RX), VCC...
Availability: Temporarily Unavailable
Item #: USB-Isolator -
Full speed USB 2.0 compliant port isolator with a 1000V isolation voltage. This device protects your PC or laptop while connecting USB devices wired to high voltages. It is a sealed device with three connectors for connecting with USB-Host, USB-Device and an optional port for an additional power supply (8-15VDC).RTQ-USB-Isolator
Availability: Temporarily Unavailable
Item #: SDC3260 -
Roboteq's SDC3260 is a features-packed, high-current, triple channel controller for brushed DC motors. The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to perform advanced motion control algorithms. The motors may be operated in open or closed loop speed mode, position mode or in torque mode. The SDC3260 features several Analog, Pulse and Digital I/Os which can be remapped as command or feedback inputs, limit switches, or many other functions. The...
Availability: Temporarily Unavailable
Item #: RGDC1860 -
Roboteq's RGDC1860 is a very high-current, features-packed motor controller for driving one brushed DC motors at up to 60V and 300A. The motor may be operated in open or closed loop speed mode, position mode or in torque mode. The RGDC1860 features an Analog, and several Digital and Pulse I/Os which can be remapped as command or feedback inputs, limit switches, or many other functions. The RGDC1860 accepts commands received from an RC radio, Analog potentiometer, wireless modem, or...
Availability: Temporarily Unavailable
Item #: MDC2460 -
Roboteq's MDC2460 controller is designed to convert commands received from an RC radio, Analog Joystick, wireless modem, PC (via RS232 or USB) or microcomputer into high voltage and high current output for driving two DC motors at up to 60V and 60A per channel. Using CAN bus, up to 127 controllers can be networked at up to 1Mbit/s on a single twisted pair.The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to perform advanced motion control algorithms...
Availability: Temporarily Unavailable
Item #: SDC2160S -
Fitting a very compact 70x70mm footprint, Roboteq's SDC2160S controller is designed to convert commands received from an RC radio, Analog Joystick, wireless modem, PC (via RS232 or USB) or microcomputer into high voltage and high current output for driving one DC motor at up to 60V and 40A. Using CAN bus, up to 127 controllers can be networked at up to 1Mbit/s on a single twisted pair.The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to perform...
Availability: Temporarily Unavailable
Item #: FDC3260 -
Roboteq's FDC3260 is a features-packed, high-current, triple channel controller for brushed DC motors. The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to perform advanced motion control algorithms. The motors may be operated in open or closed loop speed mode, position mode or in torque mode.The FDC3260 features several Analog, Pulse and Digital I/Os which can be remapped as command or feedback inputs, limit switches, or many other functions. The...
Availability: Temporarily Unavailable
Item #: MDC1460 -
Roboteq's MDC1460 controller is designed to convert commands received from an RC radio, Analog Joystick, wireless modem, PC (via RS232 or USB) or microcomputer into high voltage and high current output for driving one DC motor at up to 60V and 120A. Using CAN bus, up to 127 controllers can be networked at up to 1Mbit/s on a single twisted pair.The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to perform advanced motion control algorithms in Open Loop...
Availability: Temporarily Unavailable
Item #: SDC2160 -
Fitting a very compact 70x70mm footprint, Roboteq's SDC2160 controller is designed to convert commands received from an RC radio, Analog Joystick, wireless modem, PC (via RS232 or USB) or microcomputer into high voltage and high current output for driving two DC motors at up to 60V and 20A per channel. Using CAN bus, up to 127 controllers can be networked at up to 1Mbit/s on a single twisted pair.The controller features a high-performance 32-bit microcomputer and quadrature encoder inputs to...