Heli-max

This is the Canopy for the Blue and Black Dromida Ominus Quadcopter. Plastic construction. Ominus logo on top and blue accents on both sides.IncludesCanopy, key #10-DIDE1102

This is the Clear Canopy for the Heli-Max 1SQ and 1SQ V-Cam Helicopters. Clear plastic construction allows pilots to create their own color scheme. Canopy;Length: 3.7" (95mm)Width: 2.04" (52mm)Height: 0.87" (22mm)0-HMXE2222

This is the 1S LiPo Battery Charger for the 230Si Quadcopter UAV from Heli-Max. For use with the 1S 3.7V 1200mAh battery used in the 230Si Quadcopter. Selectable charge rate from 1.0 - 1.8A in .2 amp increments. Single solid LED shows charger current, single flashing LED indicates charging and all LEDs flashing indicates charge complete.0-HMXP2024

This is the AC Power Adapter for the Battery Charger used on the Heli-Max 230Si Quadcopter UAV. Input: 100-240VOutput: 6.0V/2.0A0-HMXP2025

This is the Altimeter Board for the 230Si Quadcopter UAV from Heli-Max. Replaces damaged altimeter boards. Sends altitude data to the TAGS-FX control board.0-HMXM2056

This is the Battery Door for the 230Si Quadcopter UAV from Heli-Max. Plastic construction, black in color.0-HMXE2333

This is the Battery Frame for the 230Si Quadcopter UAV from Heli-Max. Flexible plastic construction. Fastens to bottom section of main frame and holds battery in place.0-HMXE2324

This is the Bearing Set for the 230Si Quadcopter UAV from Heli-Max. Two ball bearings install on each spur gear shaft. Eight 3x6mm Ball Bearings included.0-HMXE2322

These are the optional Blade Guards for the 1Si Quadcopter from Helimax.FEATURESPlastic constructionProtects rotor blades from damage in the event of a crash, and alsoallows heli to continue to fly if it brushes up against a wall orother solid objectINCLUDESTwo Gray and two White Blade GuardsFour Mounting Screws0-HMXE2203

This is the Body/Frame for the 1Si Quadcopter from Helimax.FEATURESTwo-piece plastic constructionBattery compartment and LED light on bottom halfGray and neon green color schemeINCLUDESBody/Frame for the 1Si Quadcopter0-HMXE2244

This is the Canopy for the Heli-Max Axe 1SQ Quadcopter. Plastic construction with black, white and orange color scheme.0-HMXE2176

This is the Canopy Set in Blue for the Heli-Max 1SQ and 1SQ V-Cam Helicopters. Plastic construction. Blue, white, gray, and black color scheme. Canopy with two Black and two Blue Rotor Blades included.Length: 3.7" (95mm)Width: 2.04" (52mm)Height: 0.87" (22mm)0-HMXE2218

This is the Canopy Set in Green for the Heli-Max 1SQ and 1SQ V-Cam Helicopters. Plastic construction. Green, blue, black, gray, and white color scheme. Canopy with two Black and two Green Rotor Blades included.Canopy;Length: 3.7" (95mm)Width: 2.04" (52mm)Height: 0.87" (22mm)0-HMXE2219

This is the Canopy Set in Red for the Heli-Max 1SQ and 1SQ V-Cam Helicopters. Plastic construction. Red, white, gray, and black color scheme. Canopy with two Black and two Red Rotor Blades included.Length: 3.7" (95mm)Width: 2.04" (52mm)Height: 0.87" (22mm)0-HMXE2220

This is the Canopy Set in Yellow for the Heli-Max 1SQ and 1SQ V-Cam Helicopters. Plastic construction. Yellow, white, gray, and black, color scheme. Canopy with two Black and two Yellow Rotor Blades included.Length: 3.7" (95mm)Width: 2.04" (52mm)Height: 0.87" (22mm)0-HMXE2221

This is the Canopy in White and Black for the 1SQ V-Cam Quadcopter from Heli-Max. Molded plastic construction with white and black color scheme.0-HMXE2211

These are the Control Board Dampeners for the 1SQ Quadcopter from Heli-Max. Installs on each corner of the bottom of the control board to cushion and insulate board from shock. Four rubber Control Board Dampeners (key #6) included.0-HMXE2180

These are the Foot Pads for the 1SQ Quadcopter from Heli-Max. Installs on each motor cover on the four booms. Four rubber Foot Pads (key #11) included.0-HMXE2163

This is the Frame Battery Holder for the Heli-Max Axe 1SQ Quadcopter. Plastic construction. Battery slides into holder.0-HMXE2179

This is the Landing Gear for the 230Si Quadcopter UAV from Heli-Max. Plastic construction, black in color. IncludesFour Landing Gear Legs, key #15Four Landing Gear Pads, key #24,Eight Mounting Screws 0-HMXE2332

These are the Landing Pads for the 1Si Quadcopter from Heli-Max. Rubber construction. Installs on each leg of the bottom section of the frame, and helps to cushion landings. Four Landing Pads included.0-HMXE2246

This is the Left Front LED, Motor and Boom Set for the 1SQ V-Cam Quadcopter from Heli-Max. Replaces worn or non-functioning motor or LED lights. Motor is prewired with the connector attached. Counter clockwise motor rotation.0-HMXE2214

This is the Left Rear LED, Motor and Boom Set for the 1SQ V-Cam Quadcopter from Heli-Max. Replaces worn or non-functioning motor or LED lights. Motor is prewired with the connector attached. Clockwise motor rotation.0-HMXE2213

This is the Right Front LED, Motor and Boom Set for the 1SQ V-Cam Quadcopter from Heli-Max. Replaces worn or non-functioning motor or LED lights. Motor is prewired with the connector attached. Clockwise motor rotation.0-HMXE2212

This is the Right Rear LED, Motor and Boom Set for the 1SQ V-Cam Quadcopter from Heli-Max. Replaces worn or non-functioning motor or LED lights. Motor is prewired with the connector attached. Counter clockwise motor rotation.0-HMXE2215

This is the Left Front Motor Mount Arm for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Fastens to main frame body and holds left front motor assembly in place.0-HMXE2336

This is the Left Front Counter Clockwise Rotating Motor with LED for the 230Si Quadcopter UAV from Heli-Max. Replacement brushed motor, ready to install, with preinstalled pinion gear, wire lead and connector.0-HMXE2327

This is the Left Rear Motor Mount Arm for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Fastens to main frame body and holds left rear motor assembly in place.0-HMXE2337

This is the Left Rear Clockwise Rotating Motor with LED for the 230Si Quadcopter UAV from Heli-Max. Replacement brushed motor, ready to install, with preinstalled pinion gear, wire lead and connector.0-HMXE2328

This is the Main Frame/Body for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Black and gray in color with 230Si graphic. IncludesTop and Bottom Main Frame and Body Sections, key #2Right Front Motor Mount, key #19Left Front Motor Mount, key #20Left Rear Motor Mount, key #21Right Rear Motor Mount, key #22Section of Foam Tape0-HMXE2321

This is the Left Front or Right Rear Motor and Boom for the Heli-Max Axe 1SQ Quadcopter. Counterclockwise spinning motor preassembled to boom. Fits either the left front or right rear.0-HMXE2178

This is the Right Front or Left Rear Motor and Boom for the Heli-Max Axe 1SQ Quadcopter. Clockwise spinning motor preassembled to boom. Fits either the right front or left rear.0-HMXE2177

These are the Motor Covers for the Heli-Max Axe 1SQ Quadcopter. Plastic construction. Installs on bottom of each motor.0-HMXE2182

These are the Motor Covers for the 1SQ V-Cam Quadcopter from Helimax.FEATURESPlastic constructionCovers fasten to bottom of motor podsINCLUDESFour Motor CoversFour Mounting ScrewsFour red LED Indicators0-HMXE2184

This is the Left Front Motor and Red LED Light for the 1Si Quadcopter from Heli-Max. Prewired brushed motor and LED light with connector installs in left front pod of the bottom section of the frame.0-HMXE2240

This is the Left Rear Motor and Blue LED Lightfor the 1Si Quadcopter from Helimax.FEATURESPrewired brushed motor and LED light with connectorInstalls in left rear pod of the bottom section of the frameINCLUDESLeft rear Motor and Blue LED Light with ConnectorCOMMENTSMust be installed in left rear pod. Not interchangeable with othermotor and LED sets.0-HMXE2242

This is the Right Front Motor and Red LED Light for the 1Si Quadcopter from Helimax.FEATURESPrewired brushed motor and LED light with connectorInstalls in right front pod of the bottom section of the frameINCLUDESRight front Motor and Red LED Light with Connector0-HMXE2241

This is the Right Rear Motor and Blue LED Lightfor the 1Si Quadcopter from Helimax.FEATURESPrewired brushed motor and LED light with connectorInstalls in right rear pod of the bottom section of the frameINCLUDESRight rear Motor and Blue LED Light with ConnectorCOMMENTSMust be installed in right rear pod. Not interchangeable with othermotor and LED sets.0-HMXE2243

This is the Propeller Set for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Arrow on top of each prop indicates direction of rotation and must be matched with arrow on each arm. Two Gray and two Black Propellers included.0-HMXE2320

This is the Rear LED with Cover for the 230Si Quadcopter UAV from Heli-Max. LED with black plastic cover fastens to rear of main frame.0-HMXE2331

This is the Receiver Mount for the 1Si Quadcopter from Helimax.FEATURESPlastic constructionINCLUDESTwo Receiver Mount Straps0-HMXE2245

This is the Receiver Mount for the 230Si Quadcopter UAV from Heli-Max. Plastic construction, black in color. Fastens to bottom of main frame and holds the TAGS-FX control board in place.0-HMXE2326

This is the Right Front Motor Mount Arm for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Fastens to main frame body and holds right front motor assembly in place.0-HMXE2335

This is the Right Front Clockwise Rotating Motor with LED for the 230Si Quadcopter UAV from Heli-Max. Replacement brushed motor, ready to install, with preinstalled pinion gear, wire lead and connector.0-HMXE2330

This is the Right Rear Motor Mount Arm for the 230Si Quadcopter UAV from Heli-Max. Plastic construction. Fastens to main frame body and holds right rear motor assembly in place.0-HMXE2338

This is the Right Rear Counter Clockwise Rotating Motor with LED for the 230Si Quadcopter UAV from Heli-Max. Replacement brushed motor, ready to install, with preinstalled pinion gear, wire lead and connector.0-HMXE2329

These are the Rotor Blades for the Heli-Max Axe 1SQ Quadcopter. Flexible plastic construction withstands crashes. Two Orange and two Black Rotor Blades (key #1) included.0-HMXE2175

These are the Rotor Blades for the 1SQ V-Cam Quadcopter from Heli-Max. Molded plastic construction. Two White and two Black Rotor Blades, key #2 included.0-HMXE2210

These are the Rotor Blades for the 1Si Quadcopter from Helimax.FEATURESFlexible plastic constructionINCLUDESTwo Black and two White Rotor Blades0-HMXE2202

This is the Screw Set for the 1Si Quadcopter from Heli-Max. Steel construction. Contains all screws used in the assembly of the 1Si Quadcopter.0-HMXE7339

This is the Screw Set for the 1SQ Quadcopter from Heli-Max. All screws needed to secure control board, boom to motor housings and battery holder. Steel construction, black in color.0-HMXE2181

This is the Screw Set for the 1SQ V-Cam Quadcopter from Heli-Max. Steel construction. All screws used in the attachment of the control board, camera, and motor pods included.0-HMXE2217

These are the Spur Gears with Shafts for the 230Si Quadcopter UAV from Heli-Max. Four aluminum shafts with preinstalled plastic spur gears included.0-HMXE2323

This is the TAGS-FX Control Board for the 230Si Quadcopter UAV from Heli-Max. Replaces damaged TAGS-FX control boards. TAGS-FX with Sensor Fusion Technology integrates data received from a 3-axis gyro and a 3-axis accelerometer and immediately corrects unwanted movement in yaw, pitch and roll, and also prevents drift in any direction.0-HMXM2054

This is the TAGS-FX Controller Board for the 1Si Quadcopter from Helimax.FEATURESTAGS-FX Sensor Fusion stabilization system corrects drift as well asunwanted movement in yaw, pitch and rollPrewired and ready to installINCLUDESTAGS-FX Controller Board for the 1Si Quadcopter0-HMXM2053

This is the USB Micro SD Card Reader for the 1SQ V-Cam Quadcopter from Heli-Max. Stores images from the on-board camera for downloading into computer. 2GB capacity.0-HMXZ0002

This is the V-Cam Video/Picture Camera for the 1SQ V-Cam Quadcopter from Helimax.FEATURESCompletely assembled and prewiredRecords 1280x720 30fps videos in avi format1SQ RTF also takes 1MP still photos in JPEG formatOn-board LED indicates recordingINCLUDESV-Cam Video/Picture Camera, key #8SPECIFICATIONSDimensions: 1-1/2 x 3/4 x 1/3" (38.1 x 19 x 8mm)COMMENTSDoes not include micro SD card. jxs 07/26/130-HMXZ0001 ...

This is the RX604FBL Receiver and 3 Axis Gyro E-Boardfor the 1/43 scale BLACK HAWK Helicopter from Helimax.FEATURESReceiver and gyro in one compact unitTAGS (Triple Axis Gyro Stabilization) type with yaw, roll andpitch axes stabilityINCLUDESReceiver and 3 Axis Gyro E-Board, key #200-HMXM2048

This is the Canopy for the Yellow and Black Dromida Ominus Quadcopter. Plastic construction. Ominus logo on top and yellow accents on both sides.IncludesCanopy, key #10-DIDE1103