Products 1-20 of 20
Show
BSI Insta-Cure Super Thin CA 1/2 oz
Price: $3.99
View
Availability: Available
Item #: BSI101 -

Insta-Cure Super Thin .5oz CA Adhesive GlueINSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface...

BSI Super-Gold + Odorless CA 1/2 oz
Price: $8.99
View
Availability: In Stock
Item #: BSI126 -

This is a half ounce bottle of Bob Smith Industries SUPER-GOLD+™ Gap Filling, Odorless, Foam Safe CA Glue. SUPER-GOLD™ and SUPER-GOLD+™ are BSI's odorless INSTA-CURE CAs. They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™'s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF's. They will not fog clear plastic. SUPER-GOLD+™...

BSI IC-2000 Rubber-Tough CA 1/2oz
Price: $4.99
View
Availability: In Stock
Item #: BSI117 -

This is a half ounce bottle of Bob Smith Industries IC-2000™ Rubber-Toughened CA Glue. IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds,...

BSI Insta-Cure+ GAP Filling 1/2oz
Price: $3.99
View
Availability: In Stock
Item #: BSI106 -

This is a half ounce bottle of Bob Smith Industries INSTA-CURE+™ Gap Filling CA Glue. INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as lamination's, INSTA-CURE+ ™ should also be used. To prevent premature curing, don't spread the glue into a thin...

BSI Maxi-Cure Extra Thick CA 1/1oz
Price: $3.99
View
Availability: In Stock
Item #: BSI111 -

MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.0-BSI111

BSI Insta-Set CA Accelerator 2oz
Price: $5.99
View
Availability: In Stock
Item #: BSI151 -

This is 2oz bottle of INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.FEATURES: Formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strengthWill not craze most plastics even clear plastic and white foam. Forces the immediate cure of all cyanoacrylates Expands gap filling ability Permits structural fillet forming Solves most...

BSI Un-Cure CA Debonder 1oz
Price: $3.99
View
Availability: In Stock
Item #: BSI161 -

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics...

BSI IC-LOC Blue Threadlocker 1/3oz
Price: $5.99
View
Availability: Available
Item #: BSI171 -

IC-LOC™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be disassembled with standard hand tools if required.0-BSI171

BSI Quik-Cure 5 Min Epoxy 4.5oz
Price: $9.99
View
Availability: In Stock
Item #: BSI201 -

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™...

BSI Quik-Cure 5 Min Epoxy 9oz
Price: $15.99
View
Availability: In Stock
Item #: BSI202 -

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™...

BSI Mid-Cure 15 Min Epoxy 9oz
Price: $15.99
View
Availability: In Stock
Item #: BSI204 -

MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.0-BSI204

BSI Slow-Cure 30 Min Epoxy 4.5oz
Price: $9.99
View
Availability: In Stock
Item #: BSI205 -

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength...

BSI Slow-Cure 30 Min Epoxy 9oz
Price: $15.99
View
Availability: In Stock
Item #: BSI206 -

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength...

Foam cure foam glue 1.oz
Price: $2.99
View
Availability: In Stock
Item #: bsi141 -

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it's curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when...

IC-LOC HIGH STRENGTH THREAD LOCKER RED
Price: $5.99
View
Availability: In Stock
Item #: BSI-173H -

IC-LOC™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-LOC Red™ will maintain its strength up to 490° F.0-BSI-173H

Insta-Clean Sticker Remover 2 Fl oz
Price: $3.99
View
Availability: Available
Item #: BSI-100H -

BSI INSTA-CLEAN Sticker Remover works on all surfaces, including glass, cardboard, plastic, fiberglass and everything else. INSTA-CLEAN is ideal for removing price stickers and their adhesive residue. INSTA-CLEAN will also remove scuff marks that regular household cleaners won't touch.Spray directly onto the sticker to be removed. Let stand for 1 to 5 minutes and then peel off sticker and wipe clean.Works On:StickersSticker ResidueResidue on GlassResidue on Fiberglass0-BSI-100H ...

MAXI-CURE / INSTA-SET 2 FL OZ.
Price: $11.99
View
Availability: In Stock
Item #: BSI-157H -

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of...

INSTA-FLEX 1 OZ
Price: $9.99
View
Availability: Available
Item #: BSI-119 -

Insta-Flex™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated with INSTA-SET™. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE™, INSTA-FLEX™ still has good penetrating qualities and its application can be easier to control. For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete...

MID-CURE 15 MIN. EPOXY 4.5 OZ
Price: $7.99
View
Availability: In Stock
Item #: BSI203 -

MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.0-BSI203

Foam Cure EPP Foam Glue 4oz
Price: $8.99
View
Availability: In Stock
Item #: BSI142H -

FOAM-CURE is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it's curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE will act like a contact cement when...