Products 1-10 of 10
Item #: A000035 -
This valuable little book offers a thorough introduction to the open-source electronics prototyping platform that's taking the design and hobbyist world by storm. Getting Started with Arduino gives you lots of ideas for projects and helps you get going on them right away. To use the introductory examples in this book, all you need is a USB Arduino, USB A-B cable, and an LED. This 128-page book is a greatly expanded follow-up to the author's original short PDF that's available on the Arduino...
Item #: T020010 -
The Sensor Shield v.2 allows you to hook up the TinkerKit Sensors and Actuators directly to the Arduino, without the use of the breadboard. It has 12 standard TinkeKit 3pin connectors. The 6 labeled I0 through I5 are Analog Inputs. The ones labeled O0 through O5 are Analog Outputs connected to the PWM capable outputs of the Arduino Board (it is possible to change these to Digital Inputs, in which case they will report either HIGH or LOW, but nothing in between).On a Standard Arduino...
Item #: E000017 -
The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4. It has 9 digital input/output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a battery to get started. The LilyPad Arduino USB differs from previous LilyPad boards in...
Item #: A000095 -
The Arduino Esplora is a microcontroller board derived from the Arduino Leonardo. The Esplora differs from all preceding Arduino boards in that it provides a number of built-in, ready-to-use setof onboard sensors for interaction. It's designed for people who want to get up and running with Arduino without having to learn about the electronics first.The Esplora has onboard sound and light outputs, and several input sensors, including a joystick, a slider, a temperature sensor, an...
Item #: A000003 -
The Arduino Mini is a miniaturized version of the Arduino board (without the USB port). This board comes fully assembled with pins, and an ATMega328 preloaded with the Arduino bootloader.Minimal dimensions (30x18mm) allow space saving. It use an ATMEGA168 with 16K of program space and it is usable with USB/Serial converter for programming and to add the USB port. 0-A000003 Arduino Mini Main Page Free Open-Source IDE ...
Item #: A000005 -
Arduino Nano is a surface mount breadboard embedded version with integrated USB. It is small, complete, and breadboard friendly. It has everything that Diecimila has (electrically) with more analog input pins and onboard +5V AREF jumper. Physically, it is missing power jack and power select jumper. Since the Nano automatically senses and switches to the higher potential source of power, there is no need for the power select jumper. 3.0 Version with Atmega3280-A000005 Free Open-Source IDE...
Item #: A000014 -
Used with Arduino Mini to program it or add a USB port.0-A000014 Free Open-Source IDE
Item #: A000007 -
Zigbee Shield for the Arduino Board. The Zigbee module is the NEW Maxstream Series 2 XBee™ ZigBee OEM RF Module with on board chip antenna, up to 100m distance transmission. Board comes fully assembled and tested (without Arduino board) 0-A000007
Item #: A000064 -
The Wireless SD shield allows an Arduino board to communicate wirelessly using a wireless module. It is based on the Xbee modules from Digi, but can use any module with the same footprint. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/usb replacement or you can put it into a command mode and configure it for a variety of broadcast and mesh networking options. The shields breaks out each of the Xbee's pins to a...
Item #: A000053 -
The Arduino Micro is a microcontroller board based on the ATmega32u4, developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a...